Vintage Ship Salvaged Hallborn Brass Nautical Light
Quantity: 22 Pieces In Stock
Free Shipping in the continental US
Click on the photo to see additional views of these Port and Starboard Bulkhead Lights With Copper Cover.
This is a matched pair of cast brass port and starboard bulkhead lights with copper cover. From the top of the wall mount to the bottom of the cage, both port and starboard bulkhead lights with copper cover measures 11 inches tall. The copper rain cap cover that we added measures 8 inches wide and now has a rolled outside edge. The wall mount measures 4 3/8 inches wide and has four screw holes. When mounted to the wall, this light will extend out from the wall by 8 inches. Each port and starboard bulkhead light with copper cover in this set weighs over 5 pounds, and is 100% cast brass (except the covers).
We have installed a new Westinghouse UL-Listed bulb fixture that is rated for up to 250 volts. This light takes a normal screw in house bulb of 75 watts or less. To access the bulb, you unscrew the brass cage and then unscrew the glass globe. We also stock replacement glass globes for these lights, so no need to worry about broken globes down the road. This light has some original parts and some recast parts made from other broken lights.
We take great pride in this light design. We have made a new rubber gasket to fit above the rain cap cover and a second new rubber gasket has been added to the inside housing where the globe screws in. This greatly reduces if not ends the problem with bugs and water collecting inside the globe area!
Quantity: 1 Pairs In Stock
Click on the photo to see additional views of this 6 piece set of wall mounted vintage nautical cage lights.
Each of these wall mounted vintage nautical cage lights weigh about 5 pounds. Measuring from the top of the wall mount to the bottom of the cage, they are about 10 inches tall. The wall mount is 3 3/4 inches wide and has four mount holes. When mounted to the wall, these wall mounted vintage nautical cage lights will extend out from the mounting surface by about 6 inches. The brass cages spin on and off with just a little effort, as do the glass globes. The globes are original, so you can expect minor surface wear and each and every one may not be a just like the other 5 globes in the set.
Each of these wall mounted vintage nautical cage lights have been re-wired with new Westinghouse Electrical parts that are UL-Listed and rated to work with any voltage under 250 volts. The new bulb holders take a normal screw in house bulb of 75 watts or less.
Just one 6 piece matched set in stock, so you will be shipped the 6 lights shown. Note the weathering on these lights as they came from a real working vessel.
If you have an existing junction box in the mounting surface, this light may require one of our specially designed brass adaptor plates that we sell for $20.00 each. Our adaptor plate will make a water tight connection over the junction box and makes a very clean looking installation.
Just one set in stock, so you will be shipped the 6 piece wall mounted vintage nautical cage lights shown in the photos.
Quantity: 1 Six Piece Set In Stock
Click on the photo to see additional views of this brass wall light with arm.
This is a brass wall light with arm. We’ve also added a 10 inch brass cover to dress it up a little. The light measures a total of about 12 inches long and will extend down about 7 inches. The triangular mount plate measures 3 inches on each side. There are three mount holes. Because this mount plate will not cover most standard junction boxes, we recommend adding our 6 inch brass plate for an additional $20 each. The light weighs just over 4 1/2 pounds.
This light has been re-wired, including a ground wire, with an all new bulb fixture. All electrical parts we install are UL-listed and rated to work with any voltage under 250 volts. The bulb holder takes a 75 watt or less common screw-in house bulb.
Several pieces in stock.
Quantity: 19 Pieces In Stock
Click on the photo to see additional views of these Port and Starboard Brass Nautical Lights.
From the top of the junction box to the bottom of the cage, each light measures 10 3/4 inches tall and weighs just over 6 pounds. When mounted to the wall, these port and starboard brass nautical lights will extend out from the mounting surface by just short of 7 inches. The junction box is just under 4 1/2 inches wide.
Both lights have just been re-wired with all new UL-Listed bulb holders and wiring. The new parts are all rated to work with any voltage under 250 volts. The bulb holder takes a normal screw in house bulb of 75 watts or less. The glass globes are true red and green glass. To access the bulb, you spin off the brass cage and then spin off the glass globe. If your project calls for clear glass, we can change the globes out to clear glass at no cost.
These lights are made of solid brass and will never rust. They can be used for interior or exterior projects.
Ready to place that order, or just have some questions you need help with? Just give us a call at 574-870-1571 and we can help.
Just one pair in stock so you will be shipped the port and starboard brass bulkhead nautical lights shown in the photos.
Quantity: 1 Pair In Stock