Ship Salvaged Cast Brass Bulkhead Light
Quantity: 34 Pieces In Stock
Free Shipping in the continental US
Click on the photo to see additional views of this vintage brass oceanic bulkhead light.
These vintage brass oceanic bulkhead lights are about 11 inches tall. The junction box is 4 1/4 inches wide with two mounting lugs. This light is going to extend out from the wall by about 6 1/2 inches when mounted. The light manufacturer’s name, “OCEANIC” is cast into the cage of the light.
This vintage brass oceanic bulkhead light has been run through our shop where it was totally rewired with all new UL-Listed wiring and bulb socket. Our new wiring is rated for any voltage under 250 volts, and has a pre-installed ground wire so it can be installed in a wet location. The new bulb socket accepts a common screw in house bulb of 75 watts or less. To access the bulb, you just spin off the cage and then spin off the undamaged glass globe.
Quantity: 97 Pieces In Stock
Click on the photo to see additional views of this 6 piece set of wall mounted vintage nautical cage lights.
Each of these wall mounted vintage nautical cage lights weigh about 5 pounds. Measuring from the top of the wall mount to the bottom of the cage, they are about 10 inches tall. The wall mount is 3 3/4 inches wide and has four mount holes. When mounted to the wall, these wall mounted vintage nautical cage lights will extend out from the mounting surface by about 6 inches. The brass cages spin on and off with just a little effort, as do the glass globes. The globes are original, so you can expect minor surface wear and each and every one may not be a just like the other 5 globes in the set.
Each of these wall mounted vintage nautical cage lights have been re-wired with new Westinghouse Electrical parts that are UL-Listed and rated to work with any voltage under 250 volts. The new bulb holders take a normal screw in house bulb of 75 watts or less.
Just one 6 piece matched set in stock, so you will be shipped the 6 lights shown. Note the weathering on these lights as they came from a real working vessel.
If you have an existing junction box in the mounting surface, this light may require one of our specially designed brass adaptor plates that we sell for $20.00 each. Our adaptor plate will make a water tight connection over the junction box and makes a very clean looking installation.
Just one set in stock, so you will be shipped the 6 piece wall mounted vintage nautical cage lights shown in the photos.
Quantity: 1 Six Piece Set In Stock
Click on the photo to see additional views of this small wall mounted brass nautical light .
This small wall mounted brass nautical light is commonly referred to as bulkhead light or passageway light. This light is a little smaller than most of our bulkhead lights. When mounted to the wall this small wall mounted brass nautical light will extend out by about 5 inches. The wall mount is about 4 3/4 inches wide and about 1 3/4 inches tall. The two mount holes are about 4 inches on center of each other. This small wall mounted brass nautical light measures 7 1/2 inches tall (measured from the top of the wall mount to the bottom of the globe cage). To access the bulb, you spin off the cage and the undamaged glass globe drops out.
This light has been re-wired with all new UL-Listed parts that are rated for any voltage under 250 volts. The bulb socket takes a normal screw in house bulb of 75 watts or less. This light weighs about 4 pounds and can be used for interior or exterior lighting projects.
This is the real deal! Salvaged by our crew from a vessel being cut up for scrap. Because these lights came from a real working vessel they may have minor surface wear and minor dents and dings. As you can see from the attached photos, they are nice looking lights.
Talk to us about our new brass adaptor plate that will end all of your installation problems when trying to mount vintage nautical lighting to an existing in the wall junction box. Your electrician will love it if you add our custom built adaptor plate to these lights! Our 6 inch brass adaptor plates cost $20.00 each. If you order them at the same time you order your vintage nautical lighting, we will predrill the mounting holes and attach the plates to each lights with brass screws and nuts.
Quantity: 1 Pieces In Stock
Click on the photo to see additional views of this small wall mounted nautical passageway light.
This small wall mounted nautical passageway light is made of cast brass, and weighs just over over 3 pounds. It is 7 inches long and when mounted to the wall it will extend out by 5 inches. The wall mount measures just over 4 3/4 inches wide and has two mount holes. To access the bulb fixture, unscrew the cage. The glass globe lifts out.
This light has all new wiring, including a ground wire, and a new UL Listed bulb fixture that holds a normal 65 watt house bulb or less. Rated for any voltage under 250 volts.
We have designed a brass adaptor plate that mounts to the back of the light. The plate is 6 inches in diameter and is brass, and will cover nearly any American in the wall junction box. This makes for a clean installation and provides a more finished look. The plates are $20 each and if you order the plate with your light, we will attach it at no extra charge.
Quantity: 55 Pieces In Stock