Vintage Nautical Ceiling Light w/ Cover
Quantity: 1 Piece In Stock
Free Shipping in the continental US
Click on the photo to see additional views of this vintage nautical ceiling light.
This ceiling light measures about 11 inches tall and the added brass deflector cover is about 20 inches in diameter.
The 360 degree glass Fresnel lens measures about 8 1/2 inches in diameter.
The light weighs about 25 pounds.
The ceiling mount has three mount holes that are about 4 3/4 inches on center of each other.
This light is re-wired, including a ground wire, and has a porcelain bulb socket that is UL-Listed. Rated to work with any voltage under 250 volts. It takes a common screw in house bulb of 75 watts or less.
The bulb socket can be accessed by removing the three thumb screws to open the cover.
Note: One leg is slightly bent.
You will be shipped the vintage nautical ceiling light shown in the photos.
Quantity: 1 Piece In Stock
Click on the photo to see additional views of this cast brass oblong ceiling light.
This cast brass oblong ceiling light measures about 6 inches wide, including the closures, x 9 1/2 inches long. It will extend out from the mount surface by about 5 inches. The conduit holes on one end have been fitted with brass plugs. This light weighs about 5 1/2 pounds.
This light has been rewired, including a ground wire, with all new UL-Listed parts rated for any voltage of 250 volts or less. The new bulb holder takes a normal screw in house bulb of 75 watts or less. A new hole was drilled on the back on one end for the wiring to exit.
This light has been freshly polished. The glass lens is in good shape and pretty clean. Can also be used as a wall or border light.
Call us at 574-870-1571 to order!!
Quantity: 4 Pieces In Stock
Click on the photo to see additional views of this brass hanging light with copper deflector cap.
We started out with a common ceiling mounted cast brass nautical light and made it into this classy looking vintage reclaimed nautical pendant light with copper deflector cover ready to hang with 2 1/2 feet of brass chain. We added the 8 inch copper deflector cover to greatly change the look. The light measures about 13 inches long, from the tip of the handle to the bottom of the cage. It weighs about 7 pounds. Originally this light had a steel conduit pipe attached to the side to supply the electrical power. We removed the conduit and plugged the hole with a threaded brass cap.
We then added the brass handle at the top of the nautical pendant light with copper deflector cover to polish it all off. All the old wiring and bulb holder was removed and new UL-Listed parts were re-installed that are rated to work with any voltage under 250 volts. The new bulb holder takes an Edison base bulb of 50 watts or less. To access the bulb, you just spin off the brass cage and the undamaged glass globe.
This brass hanging light with copper deflector cap will be shipped with 2 1/2 feet of chain and wire, but you will need to supply the means to attach to your ceiling.
We have 7 pieces like this in stock, however these pieces are not identical and there may be some variation between pieces.
Quantity: 7 Matched Pieces
Click on the photo to see additional views of this nautical ceiling light with deflector cover.
We have taken an original cast brass engine room/passageway light and added the 7 inch brass deflector cover to make this very unique look. When mounted to the ceiling this light will extend down about 8 1/2 inches. The two ceiling mount holes are 5 1/4 inches on center of each other. A hole has been drilled in the base of the light for the wires to feed through.
We have re-wired this light using new UL-Listed parts rated for any voltage under 250 volts. The new bulb holder takes a normal screw in house bulb of 75 watts or less. The light weighs almost 6 1/2 pounds.
Note: The brass cage is slightly misaligned relative to the glass globe (see photos).
You will be shipped the nautical ceiling light shown in the photos.
Quantity: 1 Piece in Stock