Nautical Ceiling Light With Frosted Globe
Quantity: 3 Pieces In Stock
Free Shipping in the continental US
Click on the photo to see additional views of this nautical hanging light with brass deflector cap.
We started out with a common ceiling mounted cast brass nautical light and made it into this classy looking vintage reclaimed nautical pendant light with brass deflector cover ready to hang with 2 1/2 feet of brass chain. We added the 8 inch brass deflector cover to greatly change the look. The light measures about 13 inches long, from the tip of the handle to the bottom of the cage. It weighs about 7 pounds. Originally this light had a steel conduit pipe attached to the side to supply the electrical power. We removed the conduit and plugged the hole with a threaded brass cap.
We then added the brass handle at the top of the nautical pendant light with brass deflector cover to polish it all off. All the old wiring and bulb holder was removed and new UL-Listed parts were re-installed that are rated to work with any voltage under 250 volts. The new bulb holder takes an Edison base bulb of 50 watts or less. To access the bulb, you just spin off the brass cage and the undamaged glass globe.
This nautical hanging light with brass deflector cap will be shipped with 2 1/2 feet of chain and wire, but you will need to supply the means to attach to your ceiling.
We have five pieces like this in stock, however they are not all identical and there may be some variation between pieces.
Quantity: 5 Matched Pieces
Click on the photo to see additional views of this vintage brass maritime ceiling light.
We have taken this vintage brass maritime ceiling light and added the 8 inch brass deflector cover to dress it up a little. We also covered the two original conduit holes on the sides with threaded brass plugs. Freshly polished and rewired, this light is ready to hang as soon as you unpack it from our shipping box.
When mounted to the ceiling, this vintage brass maritime ceiling light will extend down by about 9 1/2 inches. To access the bulb, you spin off the brass cage and the glass globe. The base of the light has three mounting legs. The deflector cover is mounted to the cage with three screws, so if for some reason you do not want the deflector cover, it is removable.
The Westinghouse UL listed wiring and bulb holder will work with any voltage under 250 volts. The bulb holder takes a normal screw in house bulb of 75 watts or less. We drilled a small hole in the base of the light for the wiring to feed through so it will not be visible when installed.
We have a great inventory of maritime antiques, nautical ceiling lights, and more vintage nautical décor. Just give us a call at 574-870-1571 to order!
Two pieces in stock!!
Quantity: 2 Pieces In Stock
Click on the photo to see additional views of this ceiling light w/small cover.
This light measures about 11 1/2 inches tall, and the added brass deflector cover is about 14 inches in diameter with some weathering.
The light weighs about 20 pounds.
The 360 degree glass Fresnel lens measures about 8 1/2 inches in diameter and has minor edge flaking.
The ceiling mount has three mount holes.
This light is re-wired, including a ground wire. The bulb socket is UL-Listed. Rated to work under 250 volts. It takes a common screw in house bulb of 75 watts or less.
The bulb socket can be accessed by removing the three wing nuts on the lid and opening it.
You will be shipped the ceiling light w/small cover shown in the photos.
Quantity: 1 Piece In Stock
Click on the photo to see additional views of this engine room ceiling light w/brass deflector cover.
This is an original engine room ceiling light to which we added the 8 inch wide brass deflector cover. This cast brass light will extend down from the ceiling by just about 9 inches when mounted. The cage spins on and off freely. The undamaged glass globe threads into the top section of the light.
The engine room ceiling light has been re-wired with all new UL-Listed parts that are rated for any voltage under 250 volts. We have also included a ground wire. The bulb holder takes a normal screw in house bulb of 75 watts or less, or you can use the newer compact fluorescent bulbs or LED lights with an Edison base.
This engine room ceiling light weighs about 5 1/2 pounds and can be used for interior or exterior lighting projects. The base of the light has three mounting legs. You will need a mounting surface that is about 6 inches wide. The original conduit holes have been fitted with threaded brass plugs and a new hole has been drilled on the top side to allow the wiring to exit right into the ceiling.
This is a used engine room ceiling light that was recovered during one our many different salvage operations. It will have minor surface wear from being used on a working vessel.
Quantity: 16 + Matched Pieces