Authentic Port and Starboard Bulkhead Nautical Lights
Quantity: 1 Pair in stock
Free Shipping in the continental US
Click on the photo to see additional views of these Port and Starboard Bulkhead Lights With Copper Cover.
This is a matched pair of cast brass port and starboard bulkhead lights with copper cover. From the top of the wall mount to the bottom of the cage, both port and starboard bulkhead lights with copper cover measures 11 inches tall. The copper rain cap cover that we added measures 8 inches wide and now has a rolled outside edge. The wall mount measures 4 3/8 inches wide and has four screw holes. When mounted to the wall, this light will extend out from the wall by 8 inches. Each port and starboard bulkhead light with copper cover in this set weighs over 5 pounds, and is 100% cast brass (except the covers).
We have installed a new Westinghouse UL-Listed bulb fixture that is rated for up to 250 volts. This light takes a normal screw in house bulb of 75 watts or less. To access the bulb, you unscrew the brass cage and then unscrew the glass globe. We also stock replacement glass globes for these lights, so no need to worry about broken globes down the road. This light has some original parts and some recast parts made from other broken lights.
We take great pride in this light design. We have made a new rubber gasket to fit above the rain cap cover and a second new rubber gasket has been added to the inside housing where the globe screws in. This greatly reduces if not ends the problem with bugs and water collecting inside the globe area!
Quantity: 1 Pairs In Stock
Click on the photo to see additional views of the oceanic brass wall light with junction box.
From the top of the junction box to the bottom of the cage, this oceanic brass wall light measures 10 1/2 inches tall. When mounted to the wall, this oceanic brass wall light with brass junction box will extend out from the wall by 6 inches. This nautical wall light with brass junction box weighs about 8 pounds, and is 100% cast brass.
We have installed a new Westinghouse UL-Listed bulb fixture that is rated for up to 250 volts. This light takes a normal screw in house bulb of 75 watts or less. To access the bulb, you unscrew the brass cage and then unscrew the glass globe.
These lights make great dock lights, boat house lights, front door lights, and they have many interior lighting uses!
Quantity: 21 Pieces In Stock
Click on the photo to see additional views of this small wall mounted nautical passageway light.
This small wall mounted nautical passageway light is made of cast brass, and weighs just over over 3 pounds. It is 7 inches long and when mounted to the wall it will extend out by 5 inches. The wall mount measures just over 4 3/4 inches wide and has two mount holes. To access the bulb fixture, unscrew the cage. The glass globe lifts out.
This light has all new wiring, including a ground wire, and a new UL Listed bulb fixture that holds a normal 65 watt house bulb or less. Rated for any voltage under 250 volts.
We have designed a brass adaptor plate that mounts to the back of the light. The plate is 6 inches in diameter and is brass, and will cover nearly any American in the wall junction box. This makes for a clean installation and provides a more finished look. The plates are $20 each and if you order the plate with your light, we will attach it at no extra charge.
Quantity: 55 Pieces In Stock
Click on the photo to see additional views of this brass wall light with arm.
This is a brass wall light with arm. We’ve also added a 10 inch brass cover to dress it up a little. The light measures a total of about 12 inches long and will extend down about 7 inches. The triangular mount plate measures 3 inches on each side. There are three mount holes. Because this mount plate will not cover most standard junction boxes, we recommend adding our 6 inch brass plate for an additional $20 each. The light weighs just over 4 1/2 pounds.
This light has been re-wired, including a ground wire, with an all new bulb fixture. All electrical parts we install are UL-listed and rated to work with any voltage under 250 volts. The bulb holder takes a 75 watt or less common screw-in house bulb.
Several pieces in stock.
Quantity: 19 Pieces In Stock