Antique Brass Bulkhead Light With Brass Rain Cap
Free Shipping in the continental US
Click on the photo to see additional views of this small wall mounted brass nautical light .
This small wall mounted brass nautical light is commonly referred to as bulkhead light or passageway light. This light is a little smaller than most of our bulkhead lights. When mounted to the wall this small wall mounted brass nautical light will extend out by about 5 inches. The wall mount is about 4 3/4 inches wide and about 1 3/4 inches tall. The two mount holes are about 4 inches on center of each other. This small wall mounted brass nautical light measures 7 1/2 inches tall (measured from the top of the wall mount to the bottom of the globe cage). To access the bulb, you spin off the cage and the undamaged glass globe drops out.
This light has been re-wired with all new UL-Listed parts that are rated for any voltage under 250 volts. The bulb socket takes a normal screw in house bulb of 75 watts or less. This light weighs about 4 pounds and can be used for interior or exterior lighting projects.
This is the real deal! Salvaged by our crew from a vessel being cut up for scrap. Because these lights came from a real working vessel they may have minor surface wear and minor dents and dings. As you can see from the attached photos, they are nice looking lights.
Talk to us about our new brass adaptor plate that will end all of your installation problems when trying to mount vintage nautical lighting to an existing in the wall junction box. Your electrician will love it if you add our custom built adaptor plate to these lights! Our 6 inch brass adaptor plates cost $20.00 each. If you order them at the same time you order your vintage nautical lighting, we will predrill the mounting holes and attach the plates to each lights with brass screws and nuts.
Quantity: 1 Pieces In Stock
Click on the photo to see additional views of this vintage brass oceanic bulkhead light.
This vintage brass oceanic bulkhead light is about 11 inches tall. The junction box is 4 1/4 inches wide with two mounting lugs. This light is going to extend out from the wall by about 6 1/2 inches when mounted. The light manufacturer’s name, “OCEANIC” is cast into the cage of the light.
This vintage brass oceanic bulkhead light has been run through our shop where it was totally rewired with all new UL-Listed wiring and bulb socket. Our new wiring is rated for any voltage under 250 volts, and has a pre-installed ground wire so it can be installed in a wet location. The new bulb socket accepts a common screw in house bulb of 75 watts or less. To access the bulb, you just spin off the cage and then spin off the undamaged glass globe.
Quantity: 15 Pieces In Stock
Click on the photo to see additional views of these Port and Starboard Bulkhead Lights With Copper Cover.
This is a matched pair of cast brass port and starboard bulkhead lights with copper cover. From the top of the wall mount to the bottom of the cage, both port and starboard bulkhead lights with copper cover measures 11 inches tall. The copper rain cap cover that we added measures 8 inches wide and now has a rolled outside edge. The wall mount measures 4 3/8 inches wide and has four screw holes. When mounted to the wall, this light will extend out from the wall by 8 inches. Each port and starboard bulkhead light with copper cover in this set weighs over 5 pounds, and is 100% cast brass (except the covers).
We have installed a new Westinghouse UL-Listed bulb fixture that is rated for up to 250 volts. This light takes a normal screw in house bulb of 75 watts or less. To access the bulb, you unscrew the brass cage and then unscrew the glass globe. We also stock replacement glass globes for these lights, so no need to worry about broken globes down the road. This light has some original parts and some recast parts made from other broken lights.
We take great pride in this light design. We have made a new rubber gasket to fit above the rain cap cover and a second new rubber gasket has been added to the inside housing where the globe screws in. This greatly reduces if not ends the problem with bugs and water collecting inside the globe area!
Quantity: 1 Pairs In Stock
Chick on the photo to see additional views of this brass pathway nautical dock light .
This all original brass pathway nautical dock light or house light weighs about 6 pounds. From the top of the mount plate to the bottom of the cage it measures about of 10 inches. This brass pathway nautical dock light will extend out from the wall by 6 1/2 inches. The mounting surface measures 4 1/2 inches in diameter and has 3 mount holes. The cage and globe unscrew from the main housing to access the bulb holder.
We have re-wired this light, including a ground wire, and installed a new UL Listed bulb fixture that holds a normal 75 watt house bulb.
This light has seen many years of action at sea and shows some weathering.
Talk to us about our new brass adapter plate that will end all of your installation problem with any existing in the wall junction box. Our 6 inch brass adapter plates are $20.00 each. If you order them at the same time you order your lights, we will attach the plates to the lights at no extra charge.
Ready to get that order placed? Just give us a call at 574-870-1571. Most orders ship the same business day as ordered.
Quantity: 6 Pieces In Stock