|
SEE ALL THE
NAUTICAL ITEMS BELOW HERE |
WE ACCEPT VISA and MASTER CARD |
|
 |
This is an original solid cast brass nautical bulkhead
light weighting about 5 pounds each. This light is ideal option for dock
lights, seawall lights, or even interior lighting. It measures 11 1/2
inches from the top of the mount plate to the base of the cage. The
mount plate is 4 5/8 inches wide and has four screw holes. The globe is
made of glass and screws right into the top housing. The cage is also
all cast brass and screws to the outside of the top housing. This light
has been re-wired and a new 110-120 volt UL Listed bulb fixture
installed. It takes a normal screw in house bulb of 60 watts or less.
With all the old paint removed and all re-wired, they are ready to
install right out of the box.
Several matched pieces in stock and ready to ship!
Item #P1-01
$150.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS |
 |
This wall mount or commonly called bulkhead style light is
constructed of all cast brass with a copper rain cover added. These lights
comes with a cast brass junction box that provides a wall mount surface
measuring 4 1/2 inches wide. The two mount lugs have 5/16 inch mount
holes that are about 5 inches on center of each other. Each light has a
new porcelain bulb fixture that will handle a normal 65 watt house bulb
of 120 volts. We have added new wire to reach into the junction box to
make your connections. From the bottom of the brass globe cage to the
top of the junction box, this light measures just over 10 inches. The
copper rain cover measures 7 1/2 inches wide and has a finished rolled
outside edge. To access the bulb, you unscrew the brass cage and then
unscrew the glass globe. The glass globe is undamaged. The weight of
each light is about 10 pounds.
If you do not want the red and green globes, I also stock
clear globes.
$500.00 for the pair, plus shipping (LAST SET IN THIS
DESIGN)
Item #P1-02
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
If you are looking for a large
wall mount or bulkhead style light, this is one to consider. This light
measures 14 inches tall (measured from the top of the back wall mount to
the bottom of the globe cage). When mounted, this light will extend out
from the wall by almost 10 inches. The back side of the wall mount box
measures 4 5/8 X 4 5/8 inches. The rain cap cover has been added is made of copper on
this light and measures 8 3/4 inches wide. This light weights an
impressive 14 pounds. Item #P1-03 $345.00 Each Plus Shipping 24
Pieces In Stock CLICK ON PHOTO
FOR MORE VIEWS I have several of these lights in stock
that have that just polished look, or you can have one with some natural
age like you see in the photo. |
|
 |
This is a solid cast brass original bulkhead style light.
Weights just under 5 pounds. Measures just over 10 inches tall. It will
extend out from the wall by 6 1/2 inches when mounted. The mount section
is 3 7/8 inches wide with three mount lungs that extend out another 1/2
inch each.
Re-wired with a new 110-120 Volt UL listed fixture that
holds a normal 60 watt house bulb.
Use this light inside or outside, it will never rust!
Item #P1-04 $150.00 Each Plus Shipping
Several pieces in stock ready for shipping.
CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
Let's start out by saying this light is a solid 7 pounds
of brass and copper. This original bulkhead style light was used in lots
of different work area on large ships. This light was designed for wet
outside locations, but can be used as a functional and decorative
fixture in your home. I sale a lot of these to clients who use them has
front door lights, dock lights, and sea wall lights. The main housing is
cast brass and the screw on cage is copper. The globe is glass, and is
undamaged. The height of this light is just short of 9 inches. When mounted
to the wall, it will extend 6 3/4 inches from the wall. The base plate
of the wall mount is 3 3/4 inches wide and has three mount holes. The
copper cage and glass globe are both threaded, and screw on to the brass
base. Photos show original wiring, but I have now re-wired this light
with a new 110-120 UL Listed fixture, and it is ready for installation!
Less than 12 Left In Stock
Item #P1-05
Price $140.00 each. Plus Shipping
CLICK
ON PHOTO FOR MORE VIEWS
|
|
 |
This is an original wall mount bulkhead nautical light that is made of
all cast brass material. It weight just about 9 pounds. When mounted to
the wall it will extend out from the wall by just over 7 inches. From
the top of the wall mount junction box to the bottom of the globe cage
it measures 10 inches tall. The back junction box has two side holes for
the power leads, but you can buy screw in brass plugs and drill a new
hole on the back side to hide all the wiring. This light has been
re-wired with new UL-Listed parts made by Westinghouse. You can use a
normal screw in house bulb 60 watts of less. The globe is a frosted
glass, and is undamaged. The cage and globe unscrew from the main part
of the light to access the bulb.
Item # P1-06
$190.00 Plus Shipping (Only one piece in stock)
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a solid cast brass ship light. This design is normally
referred to as a bulkhead design because is was designed to mount
directly to the wall with the globe pointing down. This light measures
10 inches tall ( measured from the top of the wall mount to the base of
the globe cage). When mounted, this light will extend out from the wall
by 6 inches. The widest point of this light as you look at it from the
front measures 4 1/2 inches. The wall mount measures 3 3/4 inches with
three mount lugs sticking out an additional 1/2 inch. This light weights
about 4 pounds. $150.00 each, plus shipping 5 matched pieces remain
in stock. Item #P1-07
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a nice clean original nautical bulkhead light made by
"Appleton". The grey colored base on this light is iron. The part of the
base that the brass cage threads to is aluminum. Most people call this a
Liberty Ship Light because of the construction. I did not remove this
from a Liberty Ship, this is just a style name given to lights of this
construction. Measures 10 1/2 inches tall, and will extend out from the
wall by 5 inches when mounted. The mount plate is 4 1/2 inches wide and
has 4 mount holes. I have re-wired this with a new 110-120 volt UL
Listed fixture, so it is ready to install.
**
Click on image to the left to see additional images **
$100.00 Plus Shipping
(only one piece in stock)
P1-08
CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This original cast brass nautical light can be used as a
ceiling or a wall light. It measures 5 x 9 inches, and will extend out
from the mounting surface by 4 inches. Re-wired with a new Westinghouse
UL Listed fixture that will hold a normal screw in 50 watt bulb, or a
short T-10 appliance bulb. Wired for normal house voltage of 120 volts.
Only two pieces!
$145.00 each, plus shipping.
Item #P1-09
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a solid cast brass vintage nautical ship light. It measures 9
1/2 inches tall (from the top of the wall mount to the base of the globe
cage). It will extend 6 1/2 inches out from the wall when mounted. The
widest point of the light measures 4 inches wide. The screw in globe is
glass, and is undamaged. The wall mount is 3 3/4 inches wide. The weight
of this light is 6 pounds. The bulb is accessed by unscrewing the cage,
and then unscrewing the globe. This light has been re-wired with a new
110-120 volt UL Listed fixture that handles a normal screw in house bulb
of 70 watts or less. $160.00 Plus Shipping (LAST ONE!!)
Item #P1-10
CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is an original cast brass small
bulkhead light. Measures 6 1/2 inches tall. When mounted, it will extend
out from the wall by 5 1/2 inches. The widest point on this light is 3
1/2 inches long. The globe is glass, and undamaged. I have re-wired this
light for 110-120 volts, and a new fixture that holds a 25 watt sewing
machine bulb has been installed. Shipped with a new bulb installed. The
back mount plate measures 2 x 4 inches and this includes the 4 lugs for
mounting. This is a 4 pound light.
**
Click on image to the left to see additional images **
Item #P1-11
$95.00 Plus Shipping Stock is very limited CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is an original set of bulkhead lights with red and
green globes. Each light measures about 9 1/2 inches tall. The wall
mount measures 4 1/2 inches wide with four mount holes. When mounted to
the wall, they will extend out from the wall by about 5 inches. The
globes are glass, and undamaged. Each light weights about 5 pounds. Both
lights have been re-wired with new Westinghouse UL Listed screw in bulb
fixtures that are rated for up to 250 volts. A normal screw in house
bulb of 65 watts or less will work perfect in these lights.
Item #P1-12
$325.00 for the pair, plus shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original solid cast brass bulkhead light
with the makers' name "JUHA". The glass globe is red and undamaged.
Measures 9 1/2 inches tall. The mount plate is 4 1/16 inches wide. When
mounted to the wall this light will extend out from the wall by 6
inches. Weight is about 5 pounds. I have re-wired this light and
installed a new 110-120 volt UL Listed bulb fixture. Any normal house
bulb will work, 45-65 watt work best.
Item #P1-13 One Piece In Stock Price $100.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This wall mount - bulkhead style light is made of all cast brass with
a glass globe. We had a client that wanted an over sized bulkhead light,
so we made this light for him. When his project was completed we had six
pieces left over. When these six pieces are gone, they are gone for
ever. These lights measure 15 inches tall (from the top of the wall
mount plate to the bottom of the globe cage). The wall mount plate
measures 4 3/4 inches wide and has 4 mount holes. When mounted to the
wall, this light will extend out from the wall by 9 inches. The globe is
6 inches wide and 7 inches long. The globe and cage assemble unscrew as
one piece to access the bulb area. The light has been wired with a new
UL-Listed bulb holder rate fro up to 250 volts. A normal screw in bulb
of 75 watts or less will work fine in this light. Our original design
for this light was for an inside application, but see no reason it could
not be used outside. Again, it is made from the same cast brass you see
in our original lights.
Item#P1-14
$145.00 Plus shipping) 6 Pieces in stock
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a matched set of solid cast brass ship lights. This design is normally
referred to as a bulkhead design because is was designed to mount
directly to the wall with the globe pointing down. This light measures
10 inches tall ( measured from the top of the wall mount to the base of
the globe cage). When mounted, this light will extend out from the wall
by 6 inches. The widest point of this light as you look at it from the
front measures 4 1/2 inches. The wall mount measures 3 3/4 inches with
three mount lugs sticking out an additional 1/2 inch. Each light weights
about 4 pounds. Both lights have been re-wired with new Westinghouse UL
Listed screw in bulb fixtures that are rated for up to 250 volts. A
normal screw in house bulb of 65 watts or less will work perfect in
these lights.
This set has been fitted with red and green glass screw in globes.
$325.00 Plus Shipping
One one set in stock!
Item #P1-15
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a solid cast brass ship light. This design is normally
referred to as a bulkhead design because is was designed to mount
directly to the wall with the globe pointing down. This light measures
10 inches tall ( measured from the top of the wall mount to the base of
the globe cage). When mounted, this light will extend out from the wall
by 6 inches. The widest point of this light as you look at it from the
front measures 4 1/2 inches. The wall mount measures 3 3/4 inches with
three mount lugs sticking out an additional 1/2 inch. This light weights
about 4 pounds. $150.00 each, plus shipping 7 matched pieces remain
in stock. Item #P1-16
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This light came from a
private collection we acquired. The prior owner indicated that this
light was recovered from a WWII Liberty Ship salvage operation. It was
also noted that this design was also used on the WWII Submarines. We
have not made any effort to restore this light as we think most new
owners may want it in the original condition. This ceiling mount light
was made by Betts & Betts Corporation. The makers' name can be found on
the globe ring.
When mounted, to the wall, this light will extend out by 6 inches. It
measures 10 1/2 inches tall as shown in the photo to the left. The globe
is glass and is undamaged.
The construction material of the main light is iron. The light will
require re-wiring if you are wanting to light it up.
Great Historical Piece!
**
Click on image to the left to see additional images **
Item #P1-17 One Piece In Stock
$95.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
Great light for the money! This is one of my project
lights here in the warehouse. I had tons of lights with missing parts,
so I started casting the missing pieces to make complete lights. This
light measures 10 1/2
inches tall. When mounted to the wall it will extend out by 7 inches.
This is a little larger than most bulkheads we stock, and the price
can't be beat! Solid Brass, and re-wired it with a new
110-120 Volt UL Listed fixture. A normal 60 watt house bulb will work in
this design.
Ready to install inside or out, it will last forever!
Item #P1-18 Two pieces left in stock!!!!!! Price
$130.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS Bulkhead lights have many
different uses for that interior or exterior project. They were designed
to be wall mount lighting for walkways and work areas. Today many people
use them as dock lighting, seawall lighting, entry way lighting for your
home or cabin. Being constructed of solid cast brass, they will never
rust or fall apart. They even look great next to your fireplace! |
|
 |
This is a very nice original cast brass bulkhead light
measuring 9 1/2 inches tall. When mounted to the wall it will extend out
about 6 inches from the wall. This light has been re-wired for 110-120
volt power and has a new UL Listed bulb Fixture that will take a normal
60 watt house bulb. You can install this light inside or outside, it
will never rust! Ready to ship, and ready to install. Only one piece
like this in stock. Item #P1-19 One Piece In Stock $150.00 plus shipping
CLICK ON PHOTO FOR MORE VIEWS |
|
 |
This is a solid cast brass bulkhead light made by F.H. Lovell and
Company of Arlington, NJ. This light measures 10 1/2 inches tall. When
mounted to the wall it will extend out by 5 inches. The wall mount on
this light measures 4 1/2 inches wide and has 4 screw holes. We have
re-wired this light and installed a new UL Listed bulb fixture that
holds a normal 60 watt house bulb. Item #P1-20 Price $150.00 Plus Shipping
We have a large stock of these lights ready to ship!
CLICK ON PHOTO FOR MORE VIEWS |
|
 |
This original heavy cast brass nautical light could be a
wall or ceiling light depending on your application. This light measures
10 inches long, 5 1/2 inches wide, and will extend out from the mounting
surface by 4 1/2 inches. It weights just under 8 pounds. It has 4 mount
holes, two on each end. The glass is undamaged, but needs some
additional cleaning. This light has been re-wired with a new
Westinghouse UL Listed bulb fixture that holds a normal house bulb, or a
T-10 appliance bulb. The fixture is rated for up to 250 volts. You have
some different options on how to run your power source. First of all,
you can run it into the original holes as shown in the photos. Second
option is to plug the original hole and drill a hole on the back side to
hide all the wires. The brass plug you see taped inside the light is the
plug we made to cover the original hole if you want to do drill a hole
in the back option.
Item #P1-21
$175.00 plus shipping (4 pieces in stock)
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a
nice original masthead style nautical / ship light. Has a makers' mark of "B.T.".
Measures 13 inches tall and about 9 inches wide. The globe is 360 degree
fresnel glass. Other than needing a little cleaning, the globe is in
very good condition. This is one of my lights that was recovered from
one of my normal salvage yard operations. This light was painted when we
found it, so we have removed the paint and polished the copper and
brass. Most of the construction of this light is made of copper and the
top handle and some of the other hardware is made of brass.
As you can see from the attached photos, I have not
cleaned the inside of this light, and it will need re-wired if you plan
of lighting it up. I can re-wire and install a new 110-120 UL Listed
fixture in this light for $50.00.
**
Click on image to the left to see additional images **
Item #P1-22
$225.00 plus shipping CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is an original copper masthead
nautical / ship light. Looks like the makers' mark reads "BT". We salvaged this
light from one of our scrap yard operations and it was painted light
green in color when found. While we have removed most of the paint and
polished the copper surface, so of the original paint can still be seen.
The globe is fresnel glass, and it is in great condition. Sometime in
life, this light has been impacted on the top, and as you can see in the
photos, the top no longer sits perfect. Normally I re-wire lights like
this but because this one had such an odd original fixture I left it in
place. This light measures about 12 inches tall. Front to back, it
measures 9 1/2 inches. The back side of this light is 10 inches wide.
The weight of this light is 12 pounds. **
Click on image to the left to see additional images **
Item #P1-23
$250.00 plus shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a monster nautical light. Check out the can of
Coca-Cola next to this 28 inch tall original ship light. You are looking
at 35 pounds of copper, brass and glass. Both globes are 360 fresnel
glass. Both globes are in good condition with just some minor edge
flaking. I have re-wired this light for 110-120 volt use. We have also
installed two new UL Listed bulb fixtures that can handle 60-100 watt
normal house bulbs. T-10 appliance bulbs work real well in these lights
because the globes are each over 6 inches tall. This light is about 10
inches wide and both bulbs are accessed from the top screw off lid that
is 8 inches wide.
This light can be mounted to the top of a pole or hung
upside down from the ceiling. Some people even suspend lights like this
with chain from the ceiling. This light would also make a great dock
light if you live on that big lake and need help finding home at night!
Item #P1-24
Price $850.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is ML Piper - Montreal Designed Anchor/Masthead
light was constructed of all copper and brass. The glass globe is 360
degree fresnel. The white stuff you see on the globe is paint, and it
can be removed. The whole light was painted white when we found it. The
globe has several chips to the raised edges, but has no holes or
cracks. These chips are common on real lights like this that come from
vessels being scrapped. This light has dents and dings that came from
years at sea, so if you are looking for a light with a new look, this
is not the one for you. You can do more polishing to this light if you
want to get more of this copper and brass look. This light measures just
short of 15 inches tall and 10 inches wide. Weight is about 18 pounds.
The original electrical system needs replaced if you want to light it
up.
tem #P1-25 Price
$280.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
Check out this oversize large original masthead light. See the coke can
on the lower right hand side to get an ideal how big this one is. This
light measures 19 inches tall. The flat back side measures 10 inches
wide with the widest point being 14 inches wide. This light is
constructed of brass and copper. The globes are fresnel glass. The
globes have some edge chips and need some serious cleaning and possible
polishing. This light has had some skin repair to correct some abuse it
suffered at sea. The top hatch cover may not be original. One of the
screws on the top hatch will not get screws in, it may need some thread
tapping. Other than that, this 27 pound monster would like to come home
with you.
We have re-wired this light with two new Westinghouse UL Listed bulb
fixtures and wire rated for up to 250 volts. The bulb fixtures handle
any normal screw in house bulb, and you could put 100 watt bulbs in this
one with no problems. We pulled the new wire into the original holes,
but one small hole in the base could hide all the wiring.
$225.00 plus shipping (WHAT A DEAL!!!!!)
Item #P1-26
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
Item #P1-27
|
|
 |
This is an original Starboard Nautical Ship Light made of
brass. Measures just under 13 inches tall. This light was designed to
fit in a corner. The widest point from side to side is 12 inches. The
globe is grass and is undamaged. The main housing needs more polish
work. The original wiring is still in place, so if you want to power
this one up, it will require a new bulb fixture and wiring.
Item #P1-28
Price $195.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
No makers' name on this nautical masthead designed
light, but it must be American or English. Made of cast brass and rolled
copper it measures 14 inches tall. The flat back is 10 1/4 inches wide,
but the housing is 12 inches wide. The top access hole is 8 3/4 inches
wide. The glass globe is fresnel and has one edge chip. The globe
measures about 7 1/2 inches tall and about 8 1/2 inches wide. The globe
is 180 degrees. Weight is about 20 pounds. The original electrical
system needs replaced if you want to light it up.
Item #P1-29 Price
$375.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a matched pair of solid cast brass bulkhead lights made by F.H. Lovell and
Company of Arlington, NJ. Each light measures 10 1/2 inches tall. When
mounted to the wall each light will extend out by 5 inches. The wall mount on
this light measures 4 1/2 inches wide and has 4 screw holes. We have
re-wired this light and installed a new UL Listed bulb fixture that
holds a normal 60 watt house bulb. The red and green globes are glass. Item #P1-30 Price $325.00
for the pair, plus shipping
One pair in stock!
CLICK ON PHOTO FOR MORE VIEWS |
|
 |
Matched set of original nautical navigation lights.
One is red (Port Side) and the other is green (Starboard Side). Constructed of all brass and copper,
they guys will last another life time. Each light weights about 18
pounds. Both lights had a badge of some sort on the front just above the
globe, but both have been removed. They each measure 15 inches tall. The
two flat back surfaces measure 10 inches. From the back corner to the
front curve of the light, they measure about 13 1/2 inches. The glass fresnel globes measure about 7 inches tall and about 10 inches wide. The
globes are 160 degree. Both light globes have light wear, but nothing
other than surface chips on the raised edges. The red and green color
comes from removable shields that slide in behind the clear globe. These
color shields can be removed so the lights reflect clear. These lights
have been re-wired with 120 Volt UL Listed fixtures that hold a normal
screw in house bulb.
Item #P1-31 Price
$550.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS Original Ships
lights of this design are becoming very hard to find as most of the
newer vessels coming in for salvage have aluminum or plastic lighting.
|
|
 |
This is an original 360
degree nautical light. This light was made by Nippon Sento, Co. Ltd.
Measures a little over 7 inches tall, and about 8 1/2 inches wide. Made
of all copper and brass. The glass globe is 360 degree fresnel and has
light wear. This light has the normal wear you would expect from a light
that has been used on a working vessel for many years. I have re-wired
this light with a new 110-120 UL Listed bulb fixture. The wires of the
power enter the bottom side on this light. Ready to install!
**
Click on image to the left to see additional images **
Item #P1-32
$135.00 Plus Shipping CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original 1940's cast brass ship's light that measures 17
inches tall and 7 1/2 inches wide. This light weights 32 pounds! We have
re-wired it with all new Westinghouse UL Listed bulb holders that accept
a normal screw in bulb of 70 watts or less. We used the original entry
points for the new wires, but a single hole in the base can be drilled
to hide all the wires when you install this light. The globes are 3/4
of an inch thick. Made of 360 degree fresnel glass. The globes have a
few flakes on the raised edges, but no cracks or holes. This light can
be used inside or outside, it will never rust! Item #P1-33 $225.00
Plus Shipping CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
Set of original Ahlemmann and Schlatter - Breman"
nautical navigation lights. One is red (for the Port Side use) and the other is green
(for the starboard side use).
Constructed of all copper, they guys will last another life time. Each
light weights about 12 pounds. They each measure 15 inches tall. The two
flat back surfaces measure 9 1/2 inches. From the back corner to the
front curve of the light, they measure about 11 inches. The glass fresnel globes measure about 7 inches tall and about 8 inches wide. The
globes are about 90-120 degree. Both light globes are in very good
condition. The red and green color comes from removable shields that
slide in behind the clear globe. These color shields can be removed so
the lights reflect clear. The red light has had the back door replaced
at some point in life. The brass handle on the top of the red light is
also been replaced at some point in time. These lights have a few dings
and have been on a working vessel for many years The
original electrical system needs replaced if you want to light them up.
Item #P1-34 Price
$550.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is an original 360
degree nautical light. This light was made by Nippon Sento, Co. Ltd.
Measures a little over 8 1/2 inches tall with the top bail down, and
about 8 1/2 inches wide. Made of all copper and brass. The glass globe
is 360 degree fresnel and has light wear. This light has the normal wear
you would expect from a light that has been used on a working vessel for
many years. I have re-wired this light with a new 110-120 UL Listed bulb
fixture. The wires of the power enter a new hole that I drilled on the
bottom. The original hole the wired entered has been sealed with a
removable sealer that will dry clear in color. Ready to install!
**
Click on image to the left to see additional images **
Item #P1-35
$145.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
Looking for a monster light? This original all brass and
copper masthead light measures 25 inches tall and weights in at 35
pounds. At the widest point it measures 13 1/2 inches wide with the flat
back side measuring 10 inches wide. Both globes are fresnel glass. Each
globe as some edge flaking, but no cracks or holes. This light has been
re-wired with two Westinghouse UL listed bulb fixtures that handle
normal screw in house bulbs. The new bulb fixtures are rated up to 250
volts, so they work just fine with normal house voltage. The housing of
this light has a few minor dents and dings, but I still rate the overall
condition as good.
Item #P1-36
$750.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a very nice set of original nautical lights. They measure 9
1/2 inches tall. he globes are glass and undamaged. These lights were
designed as electric lights. I have shown a photo of one light that has
an electric pod, and the other (not shown) has and oil burner that looks
just like the electric pod. Great pair of lights!
Item #P1-37
One set in stock.
Price $295.00 for the pair. Plus shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
Last One! This wall mount nautical style light is
made of all cast brass. It will extend out from the wall by 7 1/2 inches
when mounted. From the top of the wall mount to the bottom of the globe
gage this light measures about 9 inches tall The globe is glass, and
undamaged. This light has been re-wired with Westinghouse UL Listed
parts and will take a normal house bulb of 25 watts or less. Operates on
110-120 volts.
Item #P1-38
SALE!!!!! $100.00 Plus Shipping (LAST ONE)
|
|
 |
This is an original all brass Perko
nautical light. Has a 360 degree glass fresnel globe with light wear.
Measures 15 inches tall and about 9 1/2 inches wide. Could use some more
polishing to the brass, but most of the old paint is already removed. I
have re-wired this light and installed a new 110-120 volt UL Listed bulb
fixture. If you look at the photo showing the inside of the light, I
added a piece of pressure treated wood below the light to raise the
position of the bulb to better match the globe position. Item #P1-39
$295.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a very nice original nautical light made of all
brass. The globe is 360 degree fresnel glass and is in great condition.
The light measures 11 1/2 inches tall and 10 1/2 inches wide. The top
tag indicates it was originally a red navigation light. I am sure it
must have had a red insert that is no longer with it, as the outside
globe you see in it is original. This light is pre-wired with a new
110-120 UL Listed fixture, and is ready to install! You can use a normal
60 watt house bulb, or a T-10 Appliance Bulb work real well in these
lights.
Item #P1-40
$325.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
(Very close match
to P1-43 and P1-58) |
|
 |
This is one of the older original cast brass
double masthead lights made by Perko in Miami Florida. As shown in the
photo to the left, this light measures 18 inches tall and 7 inches wide
(not counting the mount legs on the base). The top and bottom covers
unscrew to provide access to the bulb area. Since the photos were shot,
this light has now been re-wired. Two new UL Listed bulb fixtures were
installed and normal screw in house bulbs 60 watts or less will work in
this light. Weight is about
18 pounds.
This is a nice original light for the money!
Item #P1-41 $240.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This mast head light remains painted because you will
find no shiny brass or copper under that green paint. This light
measures 17 inches tall, 12 1/2 inches wide, and 9 inches front to back.
The globe is fresnel glass. The globe has a few chips on the raised
edges but has no cracks.
This light has now been re-wired with a new 110-120 Volt UL Listed
Bulb Fixture. Ready to install!
Item #P1-42
Price $175.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
HAVE
YOU LOOKED AT THE OTHER 9 PAGES OF STUFF WE HAVE ON THIS
WEB-SITE?????????? YOU ARE JUST LOOKING AT PAGE ONE RIGHT NOW! |
|
 |
This is a very nice original nautical light made of all
brass. The globe is 360 degree fresnel glass and is in great condition.
The light measures 11 1/2 inches tall and 10 1/2 inches wide. The top
tag indicates it was originally a red navigation light. I am sure it
must have had a red insert that is no longer with it, as the outside
globe you see in it is original. This light is pre-wired with a new
110-120 UL Listed fixture, and is ready to install! You can use a normal
60 watt house bulb, or a T-10 Appliance Bulb work real well in these
lights.
Item #P1-43
$325.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
(Very close match
to P1-40 and P1-58)
|
|
 |
This is an original H.L. Piper masthead light that is made
of copper and brass. Measures just over 13 inches tall. The flat back
side measures 10 1/2 inches wide, but the widest point of this light is
12 inches wide. From the back to the front it measures 11 1/2 inches.
The hole you see on the flat back side is where the original electrical
wires entered the light. I have re-wired this light with a new 110-120
Volt UL Listed fixture. I installed 12+ inches of extra wire so you can
pull the wire into the original hole, or you can run it into a new hole
anywhere you want in the housing. The two screw holes you see on the
front near the bottom were part of some sort of barcket that held this
light in place on the vessel. These two holes plus the one on the flat
back side can be sealed close with clear sealer if you want to make it
water tight.
Item #P1-44 $295.00 plus shipping.
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
Last One! This wall mount nautical style light is
made of all cast brass. It will extend out from the wall by 8 inches
when mounted. From the top of the wall mount to the bottom of the globe
gage this light measures about 11inches tall The globe is glass, and
undamaged. This light has been re-wired with Westinghouse UL Listed
parts and will take a normal house bulb of 60 watts or less. Operates on
110-120 volts.
Item #P1-45
SALE!!!!! $120.00 Plus Shipping (LAST ONE)
|
|
 |
This is an original brass nautical light measuring 14 inches tall. The
flat back side measures 9 inches wide. The globe is 180 degree fresnel
glass. The glass is undamaged, but could use some cleaning. We have
removed the pain and polished this light, but it could use some
additional cleaning. We have removed to old wiring and re-wired this
light for 110-120 volts. A new UL Listed bulb fixture has been installed
that takes a normal screw in house bulb of 75 watts or less. A T-10
Appliance bulb is strongly recommended to get the best lighting out of
this item. This light weights 8 pounds.
Item #P1-46
$200.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a one for the record books. This
light is constructed of either pewter or lead and has cast brass trim.
It was made by "Telford, Grier, Mackay and Company, 11 Fairley Street,
Glasgow. Measures 14 1/2 inches tall. Check out the big light bulb in
this housing! As you can see in the photos, this is a very clean light
with some light wear. The lens is glass and undamaged. The four brass
wing nuts that hold the hatch cover in place move freely. I have not
tested the function of the bulb or electrical system in this light.
This light weights 16 pounds. **
Click on image to the left to see additional images **
Item #P1-47
$225.00 plus shipping CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original ship's light constructed of copper. It
measures 19 inches tall and about 8 inches wide. The globes are 360
degree fresnel glass. The globes have very minor wear, but no cracks or
holes. The copper housing has a few dents and dings from all the years
at sea, but it remains a very solid housing. This light can be used
inside or out, it will never rust apart!
This light has been re-wired. Two new UL
Listed bulb fixtures were installed and normal screw in house bulbs 60
watts or less will work in this light. We placed the new wires in the
original holes, but you can drill one hole in the base and hide all the
wires when installing.
Weight is about 12 pounds.
Item #P1-48 $225.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
 |
This is an original copper and brass nautical light
measuring 12 inches tall. The base is 10 inches wide and has three mount
holes. The top is 7 1/2 inches wide. The globe is 360 degree fresnel
glass. The globe has a little edge chipping but noting too serious. We
have removed the pain and polished this light, but it could use some
additional cleaning. We have removed to old wiring and re-wired this
light for 110-120 volts. A new UL Listed bulb fixture has been installed
that takes a normal screw in house bulb of 75 watts or less. A T-10
Appliance bulb is strongly recommended to get the best lighting out of
this item. This light weights 7 1/2 pounds.
This light is stamped "Made in England", but we do not know
the maker.
Item #P1-49
$195.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a very impressive copper and brass constructed
original Mast Head light. This light measures 12 3/4 inches tall (not
counting the top handle), and is 10 3/4 inches wide, and 11 inches deep.
The 180 degree fresnel glass globe is undamaged.
I have re-wired this light with a new 110-120 Volt UL listed fixture,
so it is ready for installation!
Item #P1-50
Priced $275.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is an original copper and brass Masthead light made by
"BT". This light measures 12 inches tall. The flat back side is 10
inches wide. From the back side to the from side it measures 9 1/2
inches. The globe is 180+ degree fresnel glass. The glass is in great
condition. A new UL Listed bulb fixture has been installed that takes a
normal screw in house bulb of 75 watts or less. A T-10 Appliance bulb is
strongly recommended to get the best lighting out of this item. This
light weights 10 pounds. Item P1-51 $265.00 Plus
Shipping CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is a matched set of original ship lights. All brass
construction. Each light measures 18 inches tall, and 7 inches wide. The
fresnel globes are plastic. The globes are both 360 degree, but the back
section of the globe is covered by the housing. These could be made into
360 degree lights with a little work. Original wiring and bulb fixtures
need replaced if you are going to light these up.
Item #P1-52
Two Piece Set Price $225.00 Plus Shipping CLICK ON PHOTO
FOR MORE VIEWS |
|
 |
This is a very nice Italian made original nautical ship
light. It measures 11 1/2 inches tall, and 7 1/2 inches wide. The globe
is 360 degree fresnel glass and it is damage free. A new UL Listed bulb
fixture has been installed that takes a normal screw in house bulb of 75
watts or less. A T-10 Appliance bulb is strongly recommended to get the
best lighting out of this item. This light weights 8 pounds. All the
holes old mount holes you see in the base have been sealed with clear
sealer. When you are ready to mount this light, you can use one of the
old holes, or drill ones to fit your needs.
I normally have this same light in sets of three listed on
Page 2.
Item #P1-53
$195.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This original copper and brass ship's light measures 20 inches
tall. At the widest point, this light measures 13 1/2 inches wide. Both
globes are fresnel glass, and are in good condition with light
wear. This light has been re-wired with two Westinghouse UL listed bulb
fixtures that handle normal screw in house bulbs. The new bulb fixtures
are rated upto 250 volts, so they work just fine with normal house
voltage. The housing has a few minor dents and dings, but I still call
it in good condition. This light weights 16 pounds.
Item #P1-54
$350.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is an original ship's light constructed of cast brass.
It measures 19 inches tall and about 7 inches wide. The globes are 360
degree fresnel glass. The globes are very clean and little if any wear.
This light can be used inside or out, it will never rust apart! You can
mount it on a post, on top of the sea wall, or even hang it upside down
from the ceiling.
This light has been re-wired. Two new UL
Listed bulb fixtures were installed and normal screw in house bulbs 60
watts or less will work in this light. We placed the new wires in the
original holes, but you can drill one hole in the base and hide all the
wires when installing.
Weight is about 20 pounds.
Item #P1-55 $260.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This original ship light was made by J.H. Peters and Bey in
Hamburg. The globe is 360 degree, but only 120 degrees can be seen due
to the back cover/frame. The globe as some wear, but noting serious.
This light measures 12 inches tall. The base is 8 1/4 X 8 1/4 inches. A
new UL Listed bulb fixture has been installed that takes a normal screw
in house bulb of 75 watts or less. A T-10 Appliance bulb is strongly
recommended to get the best lighting out of this item. This light
weights 8 pounds.
Item
#P1-56
$190.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original ship's light constructed of copper. It
measures 19 inches tall and about 8 inches wide. The globes are 360
degree fresnel glass, but they are only exposed 165 degrees. The globes
have very little if any wear. The copper housing has a few dents, dings,
and minor holes from all the years at sea, but it remains a very solid
housing. I would not recommend installing this light outside do to the
holes in the housing.
This light has been re-wired. Two new UL
Listed bulb fixtures were installed and normal screw in house bulbs 60
watts or less will work in this light. We placed the new wires in the
original holes, but you can drill one hole in the base and hide all the
wires when installing.
Weight is about 12 pounds.
Item #P1-57 $195.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a very nice original nautical light made of all
brass. The globe is 360 degree fresnel glass and is in great condition.
The light measures 11 1/2 inches tall and 10 1/2 inches wide. The top
tag indicates it was originally a red navigation light. I am sure it
must have had a red insert that is no longer with it, as the outside
globe you see in it is original. This light is pre-wired with a new
110-120 UL Listed fixture, and is ready to install! You can use a normal
60 watt house bulb, or a T-10 Appliance Bulb work real well in these
lights.
Item #P1-58
$325.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
(Very close match to P1-40 and P1-43) |
|
 |
This original copper and brass ship's light measures 20 1/2 inches tall.
The flat back side measures 10 inches wide. Both globes are 180+ degree
fresnel glass, and are in great condition. This light has been re-wired
with two Westinghouse UL listed bulb fixtures that handle normal screw
in house bulbs. The new bulb fixtures are rated upto 250 volts, so they
work just fine with normal house voltage. The housing has has been
banged up from a few years of hard labor at sea, but I would still call
it in good condition. This light weights 20 pounds.
Item #P1-59
$395.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a 24 inch tall double masthead light that is made
of all copper and cast brass. Both globes are fresnel glass and
undamaged. Has two of the three mounting feet on the base missing, and
as you can see in the photos it has a dent in the front near the missing
base foot. This light has just been polished, and it turned out great!
The back of this light is 12 inches wide, and it is 9 inches deep. This
early 1900's light has the original wiring. Since the photos were shot,
this light has now been re-wired with two new bulb fixtures that handle
a normal screw in house bulbs.
Item #P1-60
$795.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
Nice original brass and copper masthead light. Measures 27 inches
tall and weights 40+ pounds. Both glass fresnel globes are in great
condition! I have re-wired and installed two new UL Listed bulb fixtures
that will hold a normal house light. A T10 Tubular bulb between 40-60
watts will work perfect. These bulb can be found at any hardware store
for less than $5.00 each.
Ready to install!
Item #P1-61
Priced $950.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
OK, for all of you people who E-Mail all
the time looking for globes, here is your shot to own a few real glass
fresnel type globes. The outside top and bottom edge measures 6 1/8
inches wide. From the top edge to the bottom edge, they measure 5 7/8
inches tall. None are perfect, they all have chips like the one shown in
the additional photos. Some has paint overspray on them, all need
cleaned. THIS
IS THE ONLY SIZE LIKE THIS I HAVE IN STOCK. Again, none of these globes
are mint, perfect, or anything close to that. I have removed all of the
ones that had major damage or cracks.
Update, I only have 6 pieces left, and they are al red in color!!!
Price now reduced to $45.00 each plus shipping.
Item #P1-62
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original cast brass hanging light
made in Italy. Measures about 12 inches tall with the handle up and
about 6 1/2 inches wide. Has the original wiring and I have not tested
the working condition. Glass globe is 360 degree and in good condition.
Item #P1-63 $100.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This original nautical light measures just short of
20 inches tall. The base is 10 1/4 inches wide with three mount holes.
Weight is 16 pounds. This light is mostly constructed of copper and has some cast brass parts
near the top. The globes are 360 degree fresnel glass with very little
wear. This light is stamped "Made In England". The missing badge on the
top would have been from "The G&B Seahorse Light Company", but it has
been ripped off while out at sea. Like most of the lights you will find
in my inventory, this light is not in mint condition, it has been used
at sea until the vessel was scrapped, and it has wear. Since the photos
were shot, this light has now been re-wired with two new bulb fixtures that handle
a normal screw in house bulbs. Item #P1-64 Price
$265.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS |
|
 |
This is an original ship's light constructed of cast brass,
and made by PERKO. It measures 17 inches tall and about 7 inches
wide. The globes are 360 degree fresnel plastic. The lower globe is
clouded, and both globes have heavy wear from many years are sea. This
light can be used inside or out, it will never rust apart! You can mount
it on a post, on top of the sea wall, or even hang it upside down from
the ceiling.
This light has been re-wired. Two new UL
Listed bulb fixtures were installed and normal screw in house bulbs 60
watts or less will work in this light. We placed the new wires in the
original holes, but you can drill one hole in the base and hide all the
wires when installing.
Weight is about 20 pounds.
Item #P1-65 $175.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This light was acquired form the estate of a long time diver who spent
most of his life diving the Great Lakes Regions of the United States. We
have no knowledge of the wreck it was recovered from, but little
question remains that it was taken from the Great Lakes Region. This 28
pound all copper and brass masthead light measures just over 25 inches
tall. Not counting the four base mounts, it measures 10 inches wide. The
glass globes have a few very minor flakes and could use some additional
cleaning. Both globes are 360 degree fresnel glass. The top cover screws
in place and is used to gain access to both bulbs. We have re-wired this
light with two new Westinghouse UL-Listed bulb holders, and it has been
re-wired for up to 250 volts. Currently the power leads are using the
original entry points, but you can drill a single hole in the base to
hide all the supply wiring. No makers' identification found, but we
think it is American or English made.
This light has been cleaned up a little and has a lot of the original
patina. You can spend a little more time cleaning and polishing, or
display it just as you see it. Either way, it will make a very
impressive use and display piece.
Item #P1-66
$700.00 Plus Shipping
One In Stock
CLICK ON PHOTO FOR MORE VIEWS |
|
 |
This original copper and brass ship's light measures 20 1/2 inches tall.
The flat back side measures 10 inches wide. Both globes are 180+ degree
fresnel glass, and are in great condition. This light has been re-wired
with two Westinghouse UL listed bulb fixtures that handle normal screw
in house bulbs. The new bulb fixtures are rated upto 250 volts, so they
work just fine with normal house voltage. The housing has a few minor
dents, but I still call it in great condition. This light weights 20
pounds.
Item #P1-67
$425.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is an original ship's light constructed of cast brass,
and made by Lovell Dressel Company in Arlington, NJ. It measures
17 inches tall and about 7 inches wide. The globes are 360 degree
fresnel plastic. Both globes are in very good condition with little
wear. This light can be used inside or out, it will never rust apart!
You can mount it on a post, on top of the sea wall, or even hang it
upside down from the ceiling.
This light has been re-wired. Two new UL
Listed bulb fixtures were installed and normal screw in house bulbs 60
watts or less will work in this light. We placed the new wires in the
original holes, but you can drill one hole in the base and hide all the
wires when installing.
Weight is about 18 pounds.
Item #P1-68 $225.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
|
|
 |
This is a very nice copper and brass original nautical
light / ship light. It measures 10 1/2 inches tall and 8 inches wide.
The globe is 360 degree fresnel glass and is in very good condition. A
new UL Listed bulb fixture has been installed that takes a normal screw
in house bulb of 75 watts or less. A T-10 Appliance bulb is strongly
recommended to get the best lighting out of this item. This light
weights 7 1/2 pounds.
Item #P1-69 $185.00 plus shipping CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is a very nice copper and brass original nautical
light / navigation light. It measures 13 inches tall, and the base is 10
inches wide with three mount holes. This light has been out to sea and
has a few dents and dings here and there. The globe is 360 degree
fresnel glass and is in good condition. A new UL Listed bulb fixture has
been installed that takes a normal screw in house bulb of 75 watts or
less. A T-10 Appliance bulb is strongly recommended to get the best
lighting out of this item. This light weights 9 pounds.
Item #P1-70
$185.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original nautical light that was made by "Mariner SA in
Brasil". Constructed of all cast brass, this light weights 15 pounds. It
has a 360 degree fresnel plastic globe that has light wear. Measures 9
1/2 inches tall, and 8 1/2 inches wide. I have
re-wired this light and installed a new 110-120 UL Listed bulb fixture
that will hold a normal house bulb. I pulled the electrical wires in
from the base and placed a removable seal in the original side hole.
**
Click on image to the left to see additional images **
Item #P1-71
$190.00.00 Plus Shipping CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This is an original cast brass engine room
light that I have added a rain cover to. The rain cover is spun brass,
and did not require any modification to the original light to install
it. When mounted to the ceiling, this light will hang down 9 inches. The
rain cover is just over 7 inches wide. This light weighs about 10
pounds! The two mounting holes are 5 1/4 inches on center apart. I have
removed the original wiring and installed a new 110 Volt UL Listed bulb
fixture and it has 4 inches of wire to make the power connection. The
base of this light makes a nice junction box, so you can really make
your final connection inside this area. The brass cage on this light is
stamped "Oceanic". This is a makers' name, not a vessel name.
Item #P1-72
Priced $150.00 Plus Shipping
Several Pieces In Stock Some May Be Slightly Different
CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
This original nautical light is constructed of mostly
copper with some cast brass trim. No makers' mark, but I am sure this is
an English design. Measures 12 inches tall, and the base is 10 inches
wide. Has a 360 degree glass fresnel globe that is in very good
condition. I have re-wired this light and installed a new 110-120 UL
Listed bulb fixture that will hold a normal house bulb. I pulled the
electrical wires in from the base and placed a removable seal in the
original side hole.
**
Click on image to the left to see additional images **
Item #P1-73
$185.00.00 Plus Shipping CLICK ON PHOTO
FOR MORE VIEWS
|
|
 |
Is this a monster light or what????? I
placed the 12 oz Coke can next to it so you can get a true indication
how big this 42 pound copper and brass light really is. This one
measures 25 inches tall, and 13 inches wide. Both globes are clear fresnel
glass. Condition of the globes is perfect.
Not shown in the photos, this light is now re-wired with two new UL
Listed 110-120 volt bulb fixtures that take a normal house bulb. For
best results, I recommend a T10 Bulb between 40-60 watts. T10 bulbs are
tubular appliance bulbs that can be found at any hardware store for
around $5.00. Each bulb fixture has separate wires so you can do
something different with each one, or tie them together with a single
power source.
This one is ready to install!
Item #P1-74 Price $1,000 Plus Shipping I have 40 lights of
this size in stock, but each one is different!
CLICK ON PHOTO
FOR MORE VIEWS |
 |
This is a very nice 1800's American wood trunk. Measures 40
inches wide, 24 1/2 inches tall, and 24 inches front to back. You have a
hidden compartment inside the main trunk that has an attached flip lid.
Not sure of the wood type. This trunk has some wear, has not been
restored but has some older repairs. As you can see in the attached
photos, this is not a common design for trunk of this period. I do not
have keys to lock it, and can't verify if the lock even works.
Shipping Notes: This is not a piece that we just can
send via the post office or FedEx. This item will have to come via
common carrier trucking were you pick it up at a terminal near you. You
determine if you want it crated or wrapped in a moving blank. If you
want it crated, this will cost $95.00 extra. You can also pick this up
at our Monticello, Indiana warehouse. Local pickup's will be required to
pay 7% Indiana Sales Tax unless your have a sales tax ID for resale.
Item #P1-75
$550.00 Plus Shipping
CLICK ON PHOTO
FOR MORE VIEWS
THIS IS THE
BOTTOM OF PAGE ONE, WE HAVE 9 MORE PAGES TO VIEW!!! Go back to the top of
this page and click on the other page links to see the rest. |