This is a very nice original oil burning nautical light. The main housing is constructed of galvanized iron and the top cover is copper. The little plate on the front of the light reads "AHLEMANN SCHLATTER BREMEN METALWARE N FABRIK". This German made light is undated, but we think it was made in the late 1950's or very early 1960's. The light measures about 19 inches tall (not counting the top handle). This is a mast head light, so the fresnel glass globe is 180+ degrees. The globe is in very good condition. The back of the light is 10 inches wide (not counting the side mounting hooks). From front to back, it is 9 inches thick. The original oil burner is in place, but we have not tested it for leaks for working condition. This light weighs 13 pounds.
Item #P8-01
Price $200.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-02
Price $150.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
This is an original iron oil burning lamp. It has a complete burner, but I have not tested the pod for leaks. The glass globe has a few issues like a 2 inch and a 1 inch crack and a few pits. The globe is still held in place with no repairs, so it make a good display. No makers' mark or date, but I think it must be 50-70 years old. Measures about 11 1/2 inches tall with the handle up. The globe is about 5 1/2 inches wide, and the gage is about 7 1/2 inches wide.
Item #P8-03
Price $115.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-04
Price $90.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-05
This is an original oil burning lantern that measures 10 inches tall (not counting the top ring). The makers' name found on the top brass vent reads "Kilborne-Sauer Fairfield Conn. U.S.A.". Globe is fresnel glass with no damage. The oil burner was missing the wick and fount, but we have replace the missing piece with a new one. I have not tested the oil pods ability to hold oil, but I see no indication of a problem. This original light has never been burned, as the inside looks like a new light. The wall hanging bracket is even included.
DO NOT MISS OUT ON THIS VERY CLEAN OIL LANTERN!
Item #P8-06
$150.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
This is a very nice original oil burning nautical light. The main housing is constructed of galvanized iron and the top cover is copper. The little plate on the front of the light reads "AHLEMANN SCHLATTER BREMEN METALWARE N FABRIK". This German made light is undated, but we think it was made in the late 1950's or very early 1960's. The light measures about 19 inches tall (not counting the top handle). This is a mast head light, so the fresnel glass globe is 180+ degrees. The globe is in very good condition. The back of the light is 10 inches wide (not counting the side mounting hooks). From front to back, it is 9 inches thick. The original oil burner is in place, but we have not tested it for leaks for working condition. This light weighs 13 pounds.
Item #P8-07
Price $200.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
This is a very nice original oil burning nautical light. The main housing is constructed of galvanized iron and the top cover is copper. The little plate on the front of the light reads "AHLEMANN SCHLATTER BREMEN METALWARE N FABRIK". This German made light is undated, but we think it was made in the late 1950's or very early 1960's. The light measures about 19 inches tall (not counting the top handle). This is a mast head light, so the fresnel glass globe is 180+ degrees. The globe is in very good condition. The back of the light is 10 inches wide (not counting the side mounting hooks). From front to back, it is 9 inches thick. The original oil burner is in place, but we have not tested it for leaks for working condition. This light weighs 13 pounds.
Item #P8-08
Price $200.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
This is a very nice original oil burning nautical light. The main housing is constructed of galvanized iron and the top cover is copper. The little plate on the front of the light reads "AHLEMANN SCHLATTER BREMEN METALWARE N FABRIK". This German made light is undated, but we think it was made in the late 1950's or very early 1960's. The light measures about 19 inches tall (not counting the top handle). This light was originally a Starboard side light and it has a green colored sliding inside lens. The inside sliding green lens can be moved to one side and the light becomes clear in color. The fresnel glass globe is about 90 degrees. The globe is in very good condition. This light was made to fit into a corner. The widest point of this light is 13 inches. From front to back, it is 10 inches thick. The original oil burner is in place, but we have not tested it for leaks for working condition. This light weighs 13 pounds.
Item #P8-09
Price $180.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-10
Price $90.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-11
This is a great looking pair of original ship's navigation lights. Each light weighs about 8 pounds and stands 14 inches tall. The 90 degree globes are made of fresnel glass. The globes have minor wear and could use some additional cleaning. Both lights have been re-wired with new Westinghouse UL-Listed parts rated for any voltage under 250 volts. The bulb holder uses a common screw in house bulb of 100 watts or less. The main housing is copper and the top lid is cast brass.
$450.00 for the pair, plus shipping
Item #P8-12
CLICK ON PHOTO FOR MORE VIEWS
This is a three piece set of original ship's navigation lights. The housing on each light is constructed of copper. The globes are 360 degree fresnel plastic. The red globe is in the best condition is just a little wear. The clear globe has some clouding and looks like the buffer got into it when it was getting polished in a few areas. The globes in the green light are in good condition, but I am not sure if it was a makers' defect or if a hot bulb caused a slight rise in one section of the globe. Either way you look at it, the globes are complete and not cracked. While this is a three piece set, the masthead light is just a little different in design, but this is not that uncommon that the masthead was just a little different than the port and starboard lights. The red and green lights measure 18 1/2 inches tall with the masthead light being more like 19 1/2 inches tall. All three measure 8 inches wide.
All three lights have been re-wired new UL Listed bulb fixtures were installed and normal screw in house bulbs 40 watts or less will work in these lights. We placed the new wires in the original holes, but you can drill one hole in the base and hide all the wires when installing. Each light has two bulb fixtures.
This is a nice set of lights, but they could use some additional TLC to make them even nicer.
Item #P8-13
$550.00 Plus shipping for the three pieces
CLICK ON PHOTO FOR MORE VIEWS
This is an original set of three nautical lights constructed of cast brass, and made by PERKO. Each ligh measures It measures 17 inches tall and about 7 inches wide. The red and green globes are 360 degree fresnel plastic. The clear globes are 360 degree fresnel glass. plastic. All the globes are in good condition with only minor wear issues. These lights can be used inside or out, and will never rust apart! You can mount them on a post, on top of the sea wall, or even hang it upside down from the ceiling.
All three lights have been re-wired new UL Listed bulb fixtures were installed and normal screw in house bulbs 60 watts or less will work in these lights. We placed the new wires in the original holes, but you can drill one hole in the base and hide all the wires when installing. Each light has two bulb fixtures.
Weight is about 18 pounds per light with the clear light being about 4 additional pounds for the glass globes.
Item #P8-14
$975.00 for three piece set, plus shipping
CLICK ON PHOTO FOR MORE VIEWS
This is a three piece matched set of original copper nautical lights. The globes are fresnel glass and show light wear but no cracks or holes. Each light measures 19 inches tall, and 7 inches wide. The base mount plate measures just short of 8 X 8 inches. The red light has the remains of a makers' plate that looks like it was made by "Tavernier". We have re-wired this light with new Westinghouse UL Listed fixtures and wire. Wired for up to 250 volts, and they use a normal screw in house bulb of 75 watts or less. We used the original entry points for the new wire, but most people will plug these holes and drill a single entry hole in the base to hide the wire during installation. These lights were designed to for outside use, but they also make interesting interior lights. Each light weights 16 pounds.
This three piece set is $725.00 Plus Shipping
Item P8-15
CLICK ON PHOTO FOR MORE VIEWS
This is a nice three piece set of original brass ship's lights. They were made in Italy. Each light measures about 18 inches tall, and 7 inches wide (not including any of the mount arms). The globes are 360 degree fresnel glass and show light wear, but no cracks or holes. Each light has two bulbs. We have re-wired this light with new Westinghouse UL Listed fixtures and wire. Wired for up to 250 volts, and they use a normal screw in house bulb of 75 watts or less. We used the original entry points for the new wire, but most people will plug these holes and drill a single entry hole in the base to hide the wire during installation. These lights were designed to for outside use, but they also make interesting interior lights. If you noticed the red light does not have the two electrical holes lined up like the other two, do not worry, it was just positioned wrong last time we put the top section back on, and we can turn it back to the right position.
This three piece set is $795.00 Plus Shipping
Item P8-16
CLICK ON PHOTO FOR MORE VIEWS
This is an extra large set of Port and Starboard Navigation light. Check out how big they are compared to the Coke can. Each light weighs 20 pounds. Each light is just under 15 inches tall. From the pointed back side to the rounded front side they measure 13 1/2 inches deep. From front corner to front corner they are 14 inches wide. The fresnel glass lens are about 10 inches wide and 7 inches tall. The fresnel glass lens in both light have considerable edge chipping as you can see in the attached photos. It may be a little hard to see in the photos, but the light on the right side has a red lens behind the clear fresnel lens, and the light on the left hand side has a green lens behind the clear fresnel lens. The top access cover is held closed by two large wing nuts, and they all turn freely. We have re-wired both lights with new UL-Listed parts made by Westinghouse. All new electrical parts are rated for any voltage under 250 volts. A normal screw in house bulb of 75 watts of less with work fine in these lights. A T-10 Appliance bulb will work even better in these lights! We show the new electrical wire entering the lights from the original conduit holes on the side of the light. If you want, we can plug the original conduit holes and drill new access holes on the back side or bottom of each light. These lights are constructed of solid brass and copper parts so they will last forever even if they are used outside!
Item #P8-17 $625.00 for the pair plus shipping
CLICK ON PHOTO FOR MORE VIEWS
Only one pair, so do not miss out on this rare sale!
This is a very hard to find set of original cast brass lights made by PERKO in Miami Florida. Each light measures 17 inches tall and 7 inches wide. Each light has four mount holes on the base that are 8 inches on center. These lights have not been re-wired and I consider the remains of the original lighting to be non-working. These lights are from the 1950's and while we have removed the paint and polished the brass, they still need some TLC. One of the top caps has part of the threads missing, but it still screws on and gets tight.
If your are looking for AMERICAN MADE, here you go!
Item #P8-18
Price: Three Piece Set $750.00 Plus Shipping
cLICK ON PHOTO FOR MORE VIEWS
This is a nice two piece set of original brass ship's lights. They were made in Italy. Each light measures about 18 inches tall, and 7 inches wide (not including any of the mount arms). The globes are 360 degree fresnel glass and show light wear, but no cracks or holes. Each light has two bulbs. We have re-wired this light with new Westinghouse UL Listed fixtures and wire. Wired for up to 250 volts, and they use a normal screw in house bulb of 75 watts or less. We used the original entry points for the new wire, but most people will plug these holes and drill a single entry hole in the base to hide the wire during installation. These lights were designed to for outside use, but they also make interesting interior lights. The red light has two top mount brackets that can be removed by screws. The base mounts are not the same on both lights, but these are the same lights other that that.
Two Piece Set is $500.00 Plus Shipping
Item P8-19
CLICK ON PHOTO FOR MORE VIEWS
To place an order, just give us a call at 574-870-1571
This is a matched set of three cast brass ship lights. The glass globes are360 degree fresnel and free of any damage. Use them inside or out, they will last for ever! Each light measures 10 1/2 inches tall and 8 inches wide. Each light weights about 18 pounds.
This three piece set has now been re-wired and is ready for installation. Each light has a new UL Listed 110-120 Volt bulb fixture with 6 inch power leads. You can pull the wires from the original hole, or drill new holes from the back side of the base.
This set of lights are designed to be wall mounted.
Item #P8-20
Set of three lights Priced $750.00 Plus Shipping
We have 2 sets of these lights in stock and ready to ship!
CLICK ON PHOTO FOR MORE VIEWS
This is a three pieces set of original ship's navigation lights. The housing and bases of these lights are made of cast brass. The fresnel glass globes are 360 degree. The globes have minor wear. The base of each light measures 8 X 8 inches, and measure 9 1/2 inches tall. You access the bulb area by turning the top knob and removing the lid. All three lights have been re-wired with new Westinghouse UL-Listed parts rated for any voltage under 250 volts. The bulb holder uses a common screw in house bulb of 100 watts or less. Each light weighs about 8 pounds.
$675.00 for the three piece set, plus shipping
Item Number P8-21
CLICK ON PHOTO FOR MORE VIEWS
You will be shipped the lights shown
This is a three pieces set of original ship's navigation lights. The housing and bases of these lights are made of cast brass. The fresnel glass globes are 360 degree. The globes have minor wear. The base of each light measures 8 X 8 inches, and measure 9 1/2 inches tall. You access the bulb area by turning the top knob and removing the lid. All three lights have been re-wired with new Westinghouse UL-Listed parts rated for any voltage under 250 volts. The bulb holder uses a common screw in house bulb of 100 watts or less. Each light weighs about 8 pounds.
$675.00 for the three piece set, plus shipping
Item Number P8-22
CLICK ON PHOTO FOR MORE VIEWS
You will be shipped the lights shown
This is a matched set (Red, Green, and Clear) brass ship lights. They measure 19 inches tall, and 7 1/4 wide. The globes are fresnel glass. Normal light wear to the glass, but no cracks. Both bulbs in each light is accessed via the top hatch. These lights were designed for outside use, but can be used inside also. Inside or outside, these base mount lights can also be inverted and hung from the ceiling with no problems.
All three lights have been freshly re-wired and new 110-120 volt UL Listed bulb fixtures have been installed. A normal screw in house bulb of 60 watts or less will work in these lights. I also recommend T-10 appliance bulbs for use in these lights. The new power lines have been run inside the original conduit leads on the side. You may consider drilling a new hole in the bottom for the power cord.
Item #P8-23
SOLD
CLICK ON PHOTO FOR MORE VIEWS
You will be shipped the lights shown.
Item #P8-24
Price $550.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
This is a 3 piece set of original brass ship's navigation lights shown in the above photos. Each light measures just under 12 inches tall and about 7 inches wide (not counting any of the mounting legs and arms. Each light weighs just over 10 pounds. The light with the clear colored lens could use some additional polish work on the back side. This is a matched set, but as you can see in the photos, some of the mounting legs and arms are a little different. The top mounting arms on the clear light are held on my four screws. Other than that, the base mount on the green light is a little different. The lens are 360 degree fresnel glass. The glass lens are in good condition with only minor wear. The hatch cover on each light is held in place by three finger nuts that spin on and off with little effort. We have installed new bulb holders in each light. The bulb holder and new wiring was made by Westinghouse electric and is stamped "UL LISTED". The new bulb holder takes a normal screw in house bulb of 65 watts or less. The wiring and bulb holder will work with any voltage under 250 volts. The new wiring exits the light using the original conduit. If you want to hide the wiring, a new hole can be drilled from the bottom side.
Item #P8-25
Price $625.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item Number P8-26
Item Number P8-27
This is an original three piece set of nautical navigation lights from a large commercial vessel. Each light in the set measures just under 17 inches tall and weighs 12-14 pounds. All three lights have clear fresnel glass lens. The light on the left hand side of the photo has the red slide in shield on the inside of the clear lens. The right hand light has the green slide in shield on the inside of the clear lens. When you light these fixtures up with the slide in shields in place, you get a red, green, and clear (Port, Starboard, and Masthead Lights). If you slide the red and green shield to the side, you end up with three clear lights.
We have re-wired all three lights with UL-Listed parts made by Westinghouse. All parts we install are rated for up to 250 volts, so normal house voltage is no problem. Each light has an upper and lower bulb. A normal screw in house bulb of 100 watts or less will work great. Each bulb is independently wired, so you can put one on a motion detector and the other on a timer, or have both come on at the same time.
The lights shown in the photos are the lights you will be shipped. The globes are glass and have no cracks but may show some wear. The housing are all brass and will have some dents , dings, and repairs. Additional cleaning will help the looks!
Item P8-28
$625.00 plus shipping for the three piece set
Click on the photo to see move views of the same light!
This is an original three piece set of nautical navigation lights from a large commercial vessel. Each light in the set measures just under 17 inches tall and weighs 12-14 pounds. All three lights have clear fresnel glass lens. The light on the left hand side of the photo has the red slide in shield on the inside of the clear lens. The right hand light has the green slide in shield on the inside of the clear lens. When you light these fixtures up with the slide in shields in place, you get a red, green, and clear (Port, Starboard, and Masthead Lights). If you slide the red and green shield to the side, you end up with three clear lights.
We have re-wired all three lights with UL-Listed parts made by Westinghouse. All parts we install are rated for up to 250 volts, so normal house voltage is no problem. Each light has an upper and lower bulb. A normal screw in house bulb of 100 watts or less will work great. Each bulb is independently wired, so you can put one on a motion detector and the other on a timer, or have both come on at the same time.
The lights shown in the photos are the lights you will be shipped. The globes are glass and have no cracks but may show some wear. The housing are all brass and will have some dents , dings, and repairs. Additional cleaning will help the looks!
Item P8-29
$625.00 plus shipping for the three piece set
Click on the photo to see move views of the same light!
Item P8-30
Item Number P8-31
Item Number P8-32
Item #P8-33
Item P8-34
This is an original brass navigational light used on the top of the vessel as a Masthead Light. The lens are clear fresnel glass. This light measures just under 17 inches tall and weights about 12 pounds.
We have re-wired this light with UL-Listed parts made by Westinghouse. All parts we install are rated for up to 250 volts, so normal house voltage is no problem. Each light has an upper and lower bulb. A normal screw in house bulb of 100 watts or less will work great. Each bulb is independently wired, so you can put one on a motion detector and the other on a timer, or have both come on at the same time.
The light shown in the photos is the light you will be shipped. The globes are glass and have no cracks but may show some wear. The housing is all brass and will have some dents , dings, and repairs. Additional cleaning will help the looks!
Item P8-35
$165.00 plus shipping
Click on the photo to see move views of the same light!
Item P8-36
Item P8-37
Item P8-38
Item Number P8-39
Item Number P8-40
Item P8-41
Item P8-42
Item P8-43
Check out this oversize large original masthead light. See the coke can on the lower right hand side to get an ideal how big this one is. This light measures 19 inches tall. The flat back side measures 10 inches wide with the widest point being 14 inches wide. This light is constructed of brass and copper. The globes are fresnel glass. The globes have some edge chips and need some serious cleaning and possible polishing. This light has had some skin repair to correct some abuse it suffered at sea. This 27 pound monster would like to come home with you.
We have re-wired this light with two new Westinghouse UL Listed bulb fixtures and wire rated for up to 250 volts. The bulb fixtures handle any normal screw in house bulb, and you could put 100 watt bulbs in this one with no problems. We pulled the new wire into the original holes, but one small hole in the base could hide all the wiring.
$195.00 plus shipping (WHAT A DEAL!!!!!)
Item #P8-44
CLICK ON PHOTO FOR MORE VIEWS
Check out this oversize large original masthead light. See the coke can on the lower right hand side to get an ideal how big this one is. This light measures 19 inches tall. The flat back side measures 10 inches wide with the widest point being 14 inches wide. This light is constructed of brass and copper. The globes are fresnel glass. The globes have some edge chips and need some serious cleaning and possible polishing. This light has had some skin repair to correct some abuse it suffered at sea. This 27 pound monster would like to come home with you.
We have re-wired this light with two new Westinghouse UL Listed bulb fixtures and wire rated for up to 250 volts. The bulb fixtures handle any normal screw in house bulb, and you could put 100 watt bulbs in this one with no problems. We pulled the new wire into the original holes, but one small hole in the base could hide all the wiring.
$195.00 plus shipping (WHAT A DEAL!!!!!)
Item #P8-45
CLICK ON PHOTO FOR MORE VIEWS
Check out this oversize large original masthead light. See the coke can on the lower right hand side to get an ideal how big this one is. This light measures 19 inches tall. The flat back side measures 10 inches wide with the widest point being 14 inches wide. This light is constructed of brass and copper. The globes are fresnel glass. The globes have some edge chips and need some serious cleaning and possible polishing. This light has had some skin repair to correct some abuse it suffered at sea. The top hatch cover may not be original. One of the screws on the top hatch will not get screws in, it may need some thread tapping. Other than that, this 27 pound monster would like to come home with you.
We have re-wired this light with two new Westinghouse UL Listed bulb fixtures and wire rated for up to 250 volts. The bulb fixtures handle any normal screw in house bulb, and you could put 100 watt bulbs in this one with no problems. We pulled the new wire into the original holes, but one small hole in the base could hide all the wiring.
$195.00 plus shipping (WHAT A DEAL!!!!!)
Item #P8-46
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-47
Item #P8-48
Looking for a monster light? This original all brass and copper masthead light measures 25 inches tall and weighs in at 35 pounds. At the widest point it measures 13 1/2 inches wide with the flat back side measuring 10 inches wide. Both globes are fresnel glass. Each globe as some edge flaking, but no cracks or holes. This light has been re-wired with two Westinghouse UL listed bulb fixtures that handle normal screw in house bulbs. The new bulb fixtures are rated up to 250 volts, so they work just fine with normal house voltage. The housing of this light has a few minor dents and dings, but I still rate the overall condition as good.
Item #P8-49
$750.00 Plus Shipping
CLICK ON PHOTO FOR MORE VIEWS
Item #P8-50
Item #P8-51
Item #P8-52
Item #P8-53
Item #P8-54
Item #P8-55
Item P8-56
Item P8-57
Item P8-58
Item P8-59
Item P8-60
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Porgey Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 26 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$75.00 Plus Shipping
Item P8-61
CLICK ON PHOTO FOR MORE VIEWS
Item P8-62
Carved from rough cut cypress wood, this Snook fish is a one of a kind work of art. It measures 24 inches long and about 12 inches tall. The thickness of this piece of carved wood is about 2 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$115.00 Plus Shipping
Item P8-63
CLICK ON PHOTO FOR MORE VIEWS
Item P8-64
Carved from rough cut cypress wood, this Snook fish is a one of a kind work of art. It measures 32 inches long and about 14 inches tall. The thickness of this piece of carved wood is about 2 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$150.00 Plus Shipping
Item P8-65
CLICK ON PHOTO FOR MORE VIEWS
Item P8-66
Item P8-67
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Sward Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 38 1/2 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$90.00 Plus Shipping
Item P8-68
CLICK ON PHOTO FOR MORE VIEWS
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Queen Snapper Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 34 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$90.00 Plus Shipping
Item P8-69
CLICK ON PHOTO FOR MORE VIEWS
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Mako Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 44 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$90.00 Plus Shipping
Item P8-70
CLICK ON PHOTO FOR MORE VIEWS
Item P8-71
Item P8-72
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Marlin Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 47 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$90.00 Plus Shipping
Item P8-73
CLICK ON PHOTO FOR MORE VIEWS
This is part of a collection of hand painted fish that we have to offer. No two pieces are alike, and the attached photos could never tell you how great they really look.
This is a Marlin Fish that was hand painted with oil paint and then clear coated. The rough cut cedar board measures 11 1/4 x 47 inches.
We normally supply these pieces to restaurants, but now you can have one for your home or office.
$90.00 Plus Shipping
Item P8-74
CLICK ON PHOTO FOR MORE VIEWS
Item P8-75